Packaging & Manufacturing Consulting
Efficiency Capability, Productivity

Categories

Locations

View items per page
Sort by
Item 8066 - 1st Stage Evaporator
Manufacturer
Crown Iron Works
Model

Unused Crown Iron Works approximately 5013 sqft (466 sqmt) 1st stage evaporator. T304 stainless steel tubes has (1064) 3/4 inch (19.05 mm) diameter x 24 feet (7315 mm) long 304 stainless steel tubes rated 15 psi/full vac (1.03 bar/full vac) design pressure. Has 58 inch (1473 mm) diameter x 24 feet (7315 mm) long shell rated +/-1 psi (-0.06/0.06 bar) design pressure. New 2004.

Place Holder
Item 6576 - Air Cannon
Manufacturer
Stanam Industries
Model
AC 4

Airchoc AC 4 air cannon. Built by Stanam Industries. This air cannon is built specifically to blow a small amount of air into your silo or hopper to break up funnels and bridges of powdery substances. Capacity: 7 cubic ft @14.7 psi, 57.5 cubic ft @ 120 psi. 8" outlet diameter. Dimensions: 46"L x 27"W x 36"H. 58 lbs. Suitable to use for all clogging issues. Easily installed and very good reliability. Operating manual included.

Place Holder
Item 6592 - Air Cannon
Manufacturer
Stanam Industries
Model
AC 4

Airchoc AC 4 air cannon. Built by Stanam Industries. This air cannon is built specifically to blow a small amount of air into your silo or hopper to break up funnels and bridges of powdery substances. Capacity: 7 cubic ft @14.7 psi, 57.5 cubic ft @ 120 psi. 8" outlet diameter. Dimensions: 46"L x 27"W x 36"H. 58 lbs. Suitable to use for all clogging issues. Easily installed and very good reliability. Operating manual included.

Place Holder
Item 5805 - Airlock
Manufacturer
Kice
Model
VJ18X14X14

Kice Airlock Model VJ18X14X14, S/N 184510C30494 with Reliance motor 1 HP, 1725 RPM

Place Holder
Item 5806 - Airlock
Manufacturer
Kice
Model
VJ18X14X14

Kice Airlock Model VJ18X14X14 S/N 184510C30500

Place Holder
Item 7140 - Barometric Condenser
Manufacturer
Kinema
Model

Kinema barometric condenser for thin film dryer. Model 844062-PY. Last used as 1st barometric on #4 thin film dryer

Place Holder
Item 5718 - Bleacher - 150 TPD Stainless
Manufacturer
DeSmet
Model
Bleacher
Capacity
2000

DeSmet stainless steel vacuum bleacher for continuous bleaching. Total capacity is 150 tons per day. Size 5' diameter with 3.5" insulation, 14' tall. Demister pad section 4' diameter x 5' tall. OAH 19 feet. Includes 2 centrifugal 3"x2" pumps. Includes 2 Krohne stainless steel mechanical flowmeters, one 1" and one 2". Includes additional side mounted small vessel and RTD for level control. Small vessel dimensions 1' diameter x 8' tall with 2" inlet. Includes 2 Masoneilan stainless steel 2" pneumatic control valves. Includes operators manual. Idled 2014 Part of bleacher system item 5766. .

Place Holder
Item 41-CA-196 - Catalyst - Sulfur Guard Bed
Manufacturer
Haldor Topsoe
Model

Catalyst - 2 drums of sulfur guard by Haldor Topsoe HTZ-4. 80-90% zinc oxide and 10-15% aluminum oxide, ans 2 drums of Haldor Topsoe A/S. Alumina: 7 drums of alumina support balls packing rings. Catalyst: 3 drum TotsuCat AMA-1 catalyst. New drums

Place Holder
Item 41-R-168 - Catalytic Converter Reactor
Manufacturer
Wagner
Model
3.9 MMBTU
Capacity
7600

Catalytic Converter designed for 3.9 MMBTU/hr. Design specifications are for 14,500 gallons/day crude methanol or 12,500 gal/day mixed alcohols. Mfg by Wagner Plate Works in 2009. Size approx 7 ft dia ID x 17 ft s/s x 30 ft overall height for approximately 7,600 gallons capacity - tube bed approx 17 ft long. Has 1,028 x 1-1/2" tubes Sch 80 stainless steel TP304L, shell cs 516-70 4 inch thick. ASME Nat'l Bd 55, MAWP 2250 psig/FV at 650 F. Converter currently loaded with approx 150 cu ft methanol catalyst - Sud Chemie MegaMax 700. Still installed - price does not include removal. Note: we have the complete reactor module as well with all pieces shown in photos plus instruments - see asset ID FP411.

Place Holder
Item 5871 - CO2 Scrubber
Manufacturer
Model

Fiberglass CO2 Scrubber Was Fermentation Scrubber. 23.5 ft tall.

Place Holder
Item 5834 - CO2 Scrubber
Manufacturer
Bionomic Industries
Model

Small CO2 Scrubber - fiberglass, 37 in dia x 17 ft 3.5 in long. Bionomic Industries

Place Holder
Item 31-V-144 - Compressor dampener pressure vessel
Manufacturer
Toromont
Model

Compressor dampener pressure vessel - ASME MAWP 425 psig at 250F, Nat'l Bd# 1302, s/n 09-113. Carbon steel. Built by Toromont n 2009 - Last used as 2nd stage booster suction bottle. Part of Compressor 31-K-120, not sold separately. NOTE: These dampeners have now been removed from the compressor. The main picture shows them as installed. Removed and ready to load

Place Holder
Item 31-V-148 - Compressor dampener pressure vessel
Manufacturer
Toromont
Model

Compressor dampener pressure vessel - ASME MAWP 425 psig at 350F, Nat'l Bd# 1303, s/n 09-114. Carbon steel. Built by Toromont in 2009. Used as 2nd stage booster suction bottle. Part of Compressor 31-K-120, not sold separately. NOTE: These dampeners have now been removed from the compressor. The main picture showS them as installed. Removed and ready to load

Place Holder
Item 31-V-160 - Compressor dampener pressure vessel
Manufacturer
Toromont
Model

Compressor dampener pressure vessel - ASME MAWP 1285 psig/FV at 350F, Nat'l Bd# 1304, s/n 09-115. Built by Toromont in 2009 - was run 42 days - like new. Carbon steel. Used as 3rd stage booster suction bottle. Part of Compressor 31-K-216, not sold separately. NOTE: These dampeners have now been removed from the compressor. The main picture shows them as installed. Removed and ready to load

Place Holder
Item 31-V-168 - Compressor dampener pressure vessel
Manufacturer
Toromont
Model

Compressor dampener horizontal pressure vessel. ASME MAWP 1285 psig/FV at 350F, NB# 1305, s/n 09-116. Carbon steel. Built in 2009 by Toromont - used 42 days - like new. Used as 3rd stage booster discharge bottle. Part of Compressor 31-K-216, not sold separately. NOTE: These dampeners have now been removed from the compressor. The main picture shows them as installed. Removed and ready to load

Place Holder
Item 31-V-172 - Compressor dampener pressure vessel
Manufacturer
Toromont
Model

Compressor dampener pressure vessel - ASME MAWP 1850 psig/FV at 250F, Nat'l Bd# 1306, s/n 09-117. Carbon steel. Used as 4th stage booster suction bottle. Part of Compressor 31-K-216, not sold separately. NOTE: These dampeners have now been removed from the compressor. The main picture shows them as installed. Removed and ready to load

Place Holder
Item 31-V-176 - Compressor dampener pressure vessel
Manufacturer
Toromont
Model

Compressor dampener pressure vessel - ASME MAWP 1850 psig/FV at 350F, Nat'l Bd# 1307, s/n 09-116. Built by Toromont in 2009 - ran 42 days - like new. Carbon steel. Used as 4th stage booster discharge bottle. Part of Compressor 31-K-216, not sold separately. NOTE: These dampeners have now been removed from the compressor. The main picture shows them as installed. Removed and ready to load

Place Holder
Item 41-V-148 - Compressor dampener pressure vessel
Manufacturer
Toromont
Model
50 gallons
Capacity
50

Horizontal pressure vessel compressor dampener. Built by Toromont in 2009 - used 42 days: Like New. ASME MAWP 1850 psig at 350F, Nat'l Bd# 1309, s/n 09-120. Physical size 16" dia x 60" for 50 gallon capacity. Used as Synloop Compressor Discharge Bottle 1. Part of compressor 41-K-140, not for sale separately. NOTE: These dampeners have now been removed from the compressor. The main picture shows them as installed. Removed and ready to load

Place Holder
Item 41-V-156 - Compressor dampener pressure vessel
Manufacturer
Toromont
Model
50 gallons
Capacity
50

Horizontal pressure vessel compressor dampener. Built by Toromont in 2009 - used 41 days: Like New. ASME MAWP 1850 psig at 350F, Nat'l Bd# 1310, s/n 09-122. physical size 16" dia x 60" for capacity of approx 50 gallons. Used as Synloop Compressor discharge dampener bottle #2. Part of compressor 41-K-140, not for sale separately. NOTE: These dampeners have now been removed from the compressor. The main picture shows them as installed. Removed and ready to load

Place Holder
Item 41-V-144 - Compressor dampener pressure vessel
Manufacturer
Toromont
Model
50 gallon
Capacity
50

Horizontal pressure vessel compressor dampener. Built by Toromont in 2009 - used 42 days: Like New. ASME MAWP 1650 psig at 250F, Nat'l Bd# 1308, s/n 09-119. Physical size 16" dia x 60". Used as Synloop Compressor Suction Bottle 1. Part of compressor 41-K-140, not for sale separately. NOTE: These dampeners have now been removed from the compressor. The main picture shows them as installed. Removed and ready to load

Place Holder
Item 41-V-152 - Compressor dampener pressure vessel
Manufacturer
Toromont
Model
50 gallons
Capacity
50

Horizontal pressure vessel compressor dampener. Built by Toromont in 2009 - used 41 days: Like New. ASME MAWP 1650 psig at 250F, Nat'l Bd# 1299, s/n 09-121. Physical size 16" dia x 60" for capacity of 50 gallons. Used as suction dampener (on top - stage 1). Part of compressor 41-K-140, not for sale separately. NOTE: These dampeners have now been removed from the compressor. The main picture shows them as installed. Removed and ready to load

Place Holder
Item 31-V-132 - Compressor dampener pressure vessel
Manufacturer
Toromont
Model

Compressor dampener pressure vessel - ASME MAWP 225 psig at 350F, Nat'l Bd# 1300. Carbon steel. Built by Toromont in 2009 - ran only 42 days - like new. Used as 1st stage booster suction bottle. Part of Compressor 31-K-120, not sold separately. NOTE: These dampeners have now been removed from the compressor. The main picture shows them as installed. Removed and ready to load

Place Holder
Item 31-V-136 - Compressor dampener pressure vessel
Manufacturer
Toromont
Model

Compressor dampener pressure vessel - ASME MAWP 215/FV at 350F, Nat'l Bd# 1301, s/n 09-112. Carbon steel. Built by Toromont in 2009 - Used as 1st stage booster discharge bottle. Part of Compressor 31-K-120 not sold separately. NOTE: These dampeners have now been removed from the compressor. The main picture shows them as installed. Removed and ready to load

Place Holder
Item 8071 - Condenser
Manufacturer
Crown Iron Works
Model

Unused Crown Iron Works 374 sqft (35 sqmt) horizontal condenser. Has (119) 3/4 inch (19.05 mm) diameter x 16 feet (4877 mm) long t304l stainless steel tubes rated -15/75 psi (-1.03/5.17 bar) design pressure at 250 deg.f (121 deg.c). Has 14 inch (356 mm) diameter x 16 ft (4877 mm) long carbon steel shell rated -15/165 psi (-1.03/11.37 bar) design pressure at 300 deg.f (149 deg.c). New 2004.

Place Holder
Item 5809 - Condenser
Manufacturer
Paget Equipment
Model

Shell & Tube Heat Condenser, Paget Equpment, S/N 06-143-A, 2006

Place Holder