Packaging & Manufacturing Consulting
Efficiency Capability, Productivity

Categories

Locations

View items per page
Sort by
Item 7631 - Centrifuge
Manufacturer
Alfa-Laval
Model
MAB 2065-24

Alfa-Laval Centrifuge MAB 2065-24. Mfg # 2925001. Worm wheel shaft 1420-1500. Revolution Counter 118-125. Includes some tools but not all. Has been sitting for quite a while Includes close coupled motor. Separation takes place in a solids-retaining bowl that can be arranged for either clarification or purification. Solids retained in bowl and removed by manually cleaning

Place Holder
Item 5198 - Centrifuge
Manufacturer
Alfa Laval
Model
CRPX 507

Alfa Laval CRPX 507 centrifuge. Tools and controls included, last used on what is described at "liqueur" and only used about 100 hours. The price is "reconditioned" with shipment in 5-7 weeks.

Place Holder
Item 5575 - Centrifuge B214 A
Manufacturer
Alfa Laval
Model
B214A

Alfa Laval B214A centrifuge. The complete unit will be reconditioned, balanced, new seals/bearings, painted. Photo shows machine prior to reconditioning - allow 4 to 6 weeks delivery. Reconditioning includes, complete disassembly of machine, sandblast and paint all carbon steel parts, remove gear pump, install end plate, Rebuild using all new parts, Bearings, seals, and O-rings(Viton), All Vibration Isolators units will be tested and come with manuals, some tools and one set of gravity discs. High speed balance will also be performed. 40hp motor will be rebuilt or new depending upon timing. Welcome to inspect the machine as tests are run to verify balance. Centrifuge can also be purchased " as is, where is " if desired.

Place Holder
Item 7117 - Centrifuge B214 C
Manufacturer
DeLaval
Model
B214C

DeLaval B214C solid bowl disc centrifuge. Serial number 3532804. Capacity approximately 36,000 to 40,000 #/hr. Motor is 40HP. Cleaned and painted, epoxy internal coating but not reconditioned. Bowl removed and crated for shipping. Very good condition

Place Holder
Item 5567 - Centrifuge B214 C
Manufacturer
Alfa Laval
Model
B214C

Alfa Laval B214C centrifuge. The complete unit will be reconditioned, balanced, new seals/bearings, painted. Photo shows machine prior to reconditioning - allow 4 to 6 weeks delivery. We can quote an "As Is" price if desired.

Place Holder
Item 7639 - Centrifuge CA-450
Manufacturer
Westfalia
Model
CA 450-06-02

Westfalia CA 450-06-02. Unit comes with control panel. Manual is available.

Place Holder
Item 7300 - Centrifuge CRPX-207
Manufacturer
Alfa Laval
Model
CRPX 207-74-A

Alfa Laval centrifuge clarifier Model CRPX 207-74-A, Serial # 2925171, 2925176, 2925170. Disk Stack 316SS. Does not include motor, tools, or controls. Quantity (3) available - priced separately.

Place Holder
Item 8003 - Centrifuge OSB-35
Manufacturer
Westfalia
Model
OSB-35-02

One (1) Reconditioned Westfalia Model OSB-35-02 Self-Cleaning centrifuge to include: Max. Hydraulic Capacity: 90 GPM, Max. Process Capacity: Varies depending on process conditions, Viton o-rings used in product contact areas, Direct-drive design, Variable shoot design (partial or full shot), Stainless steel rotating assembly, Powder-coated grey iron frame and silumin cover, 20 HP Class 1., Div. 1 explosion-proof motor - 460/480 Volt, 3 phase, 60 cycle, Heavy Phase (water) discharged by gravity, Light Phase (oil) discharged under pressure by means of a paring disk (centripetal pump), One (1) set of regulating discs, One (1) set of necessary special tools, One (1) set of spare bowl o-rings, One (1) copy of the Operation / Spare parts Manual, Feed pump not included. Customer required to supply their own feed pump.

Item 9038 - Centrifuge RSA-60 ss316
Manufacturer
Westfalia
Model
RSA-60-01-076

Westfalia RSA 60-01-076 vegetable oil separator, 316SS. Max bowl speed 6450 RPM, rated @ 13000 LPH, both liquid phases discharged under pressure, 15 KW motor 380/3/50/ 1450 RPM, manual counter pressure valve. 1987 vintage. No tools or controls. Very good condition

Place Holder
Item 8152 - Centrifuge RSA-60 ss316
Manufacturer
Westfalia
Model
RSA 60-01-076

Westfalia RSA 60-01-076 vegetable oil separator, 316SS. Max bowl speed 6450 RPM, rated @ 13000 LPH, both liquid phases discharged under pressure, 15 KW motor 380/3/50/ 1450 RPM. No tools or control panel. 1991 vintage. Used - Excellent condition

Place Holder
Item 5071 - Centrifuge RSA-60 ss316
Manufacturer
Westfaia
Model
RSA 60-01-076

Westfalia RSA 60-01-076 vegetable oil separator, 316SS. Max bowl speed 6450 RPM, rated @ 13000 LPH (57.2 gpm), both liquid phases discharged under pressure, 20 HP motor 230/460v 3/60 1750 RPM. Very good condition. The machine does include bowl insertion tools, but no controls. It was made in 1980 and used to refine or for degumming vegetable oil. We can recondition for you and add controls if desired

Place Holder
Item 6017 - Centrifuge RSE-300
Manufacturer
Westfalia
Model
RSE-300

Westfalia Model RSE-300 Self-Cleaning units Model: RSE300-01-777 - Bowl Speed: 4800 rpms - Flanged Mounted Motor - Belt Drive design. - One (1) set of special tools. - One (1) copy of the Operation / Spare parts Manual - Last Application: Used vegetable oils - VFD and control panel. - Year Built 2014 - Two (2) centrifuges available - Serial Numbers 1733- 990 and 1733-991 The machines were set up for Corn Oil and used in a biodiesel plant. They do have the ability to receive Gas Into the bowls and motors if required. The machines were built in 2014 and are in MINT condition, they ran for 9 months then were never used. Includes controls and tools. Two (2) units - priced separately - we can offer a package deal for both.

Place Holder
Item 7419 - Centrifuge RSE100
Manufacturer
Westfalia
Model
RSE 100-01-776

Westfalia RSE 100-01-776 centrifuges. As is. 1715324 & 1715325. Two available, priced separately.

Place Holder
Item 7156 - Centrifuge SAMN 15037
Manufacturer
Westfalia
Model
SAMN 15037

Westfalia SAMN 15037 centrifuge. This is a 3 phase separator. Year 1975 with a BSB 100 rotary brush strainer This machine was overhauled by Westfalia 2009 and was removed in 2011, it was in a winery and used to work around 4 weeks a year, to filter the new wine, with yearly inspections by Westfalia technical service after. Drum and mechanical parts are in very good condition (inspected by a technician during dismantling). 380V/50Hz/3 phase.

Place Holder
Item 320-EQ-340 - Decanter 2 phase CA-450
Manufacturer
Westfalia
Model
CA-450-00-32

Westfalia decanter Model CA-450-00-30, serial 1705484. Rated at 110 gpm. Amount of solids will determine flow capacity - for canola or soybean crush decanter, figure between 25 to 50 gpm capacity. Includes drive and back drive, Solid Bowl Decanter Centrifuge, 18" x 57", horizontal scroll type centrifuge constructed of centrifugally cast duplex stainless steel. Maximum bowl speed of 3,000 rpm or 2300 x G. Single flight, hard surfaced scroll conveyor equipped with sprayed tungsten carbide over entire outer diameter and plowing surface. Decanter bowl is driven by a three phase, 30 hp, AC motor mounted in line with the decanter housing which reduces space requirements. Scroll conveyor is driven by a "2 gear drive" system which consists of two Cyclo gears in series driven by a frequency controlled 10 hp secondary motor. Foundation made of painted carbon steel to raise centrifuge to convenient height for handling solids discharge. Includes Control panel, NEMA 12 design. Decanter bought in 2008, used approximately 9 months, then idled in heated process building. Like New. Part of Crush package. For a list of all components, enter "pkcrush" in the keyword search terms box.

Place Holder
Item 350-EQ-605 - Decanter 2 phase CB-505
Manufacturer
GEA Westfalia
Model
CB505-01-12

GEA Westfalia 2 phase decanter model CB505-01-12. S/N 8001 505. Has 500mm bowl diameter. V-belt drive with clutch. Includes hydraulic power pack. Built 1999. Moved to this plant in 2008, ran about 9 months then idled in heated process building. Two motors 50HP and back drive 20HP with VFD. Includes control panel (for sn 8002). Last used as Washed Curd Centrifuge

Place Holder
Item 6001 - Decanter 3-Phase
Manufacturer
Sharples
Model
P-3400

3-phase decanter Sharples P3400 Super-D-Canter. Bowl dimensions 14" x 48", beach angle 10 degree. Max speed of 4000 RPM, Max G force 3160 x G Force. Quasi-axial flow conveyor design. 316 ss rotating assembly & case and cover. P-165, Mounted to a unitized sub-base with vibration isolators. Main drive motor: 40 H.P. TEFC, 1800 RPM, 480 voltage, 3-phase, 60 cycle power required, NEMA-12 enclosure, Reduced voltage starter comes with it. No back drive motor. Removed and ready for loading. Built in 1980 - decanter was rebuilt in 2001. P.125 Gearbox Ratio - Max Allowable Torque on Gearbox 1.72kgf m. Capacity from 13 gpm to 75 gpm depending on viscosity of feed and rpm of motor. Rated at 11 ton/hr at infeed of 10% solids (264 TPD max),

Place Holder
Item 320-EQ-340B - Decanter Centrifuge 2-phase CA-220
Manufacturer
Westfalia
Model
CA 220-300

Westfalia decanter Model CA-220-300. Max bowl speed 4000 RPM. Includes drives

Place Holder
Item 9212 - Decanter Centrifuge CA-450 NEW
Manufacturer
Westfalia
Model
CA-450-00-02

Westfalia CA 450-00-02 decanter centrifuge, 316SS. NEW. Never used; still in crates. Max bowl speed 3400 RPM, 3000 G's, rated @ 110 GPM. 6.25" single lead hardsurfaced conveyor, 22 KW motor 380/3/50/1450 RPM, 52:1 cyclo gear, 7.5 KW back drive with VFD, guards, mounted on stand with control panel. Designations 00-Gravity Discharge. 02-no motor clutch. FCA Europe.

Place Holder
Item 7637 - Decanter Centrifuge CA-458
Manufacturer
Westfalia
Model
CA 458-00-02

Westfalia CA 458-00-02 decanter centrifuge, 316SS. Max bowl speed 3300 RPM, 2780 G's, 18 x 80" bowl ID. 6.25" single lead hardsurfaced conveyor, 30 KW motor 460/3/60/3535 RPM, no cyclo gearbox, 11 KW backdrive, no feed tube, guards and chutes mounted on a stand. 2000 vintage. Very good condition.

Place Holder
Item 7638 - Decanter Centrifuge CA-458
Manufacturer
Westfalia
Model
CA 458-00-02

Westfalia CA 458-00-02 decanter centrifuge, 316SS. Max bowl speed 3000 RPM, 2300 G's, 18 x 80" bowl ID. 6.25" single lead hardsurfaced conveyor, 30 KW motor 440/3/60/3535 RPM, hydraulic backdrive with 15 HP motor feed tube, chutes and control panel mounted on a stand. 1994 vintage. Very good condition.

Place Holder
Item 5379 - Decanter Centrifuge system
Manufacturer
Sharples
Model
P-3000

Used Sharples P-3000 Decanter Centrifuge System including Bowl Dimensions: 14 in x 30 in, 10 degree beach angle, 316 stainless steel rotating assesmbly and product contact parts, Three sets of plate dams for shallow, medium and deep pond settings, 4.25 inch scroll-conveyor pitch spacing, Planetary gearbox, trip-arm assembly with limit switch, and new 25 HP motor and new control panel. Delivery 6-8 weeks.

Item 7636 - Decanter Centrifuge UCC-458
Manufacturer
Westfalia
Model
UCC 458-00-02

Westfalia UCC 458-00-02 decanter centrifuges, 316SS. Max bowl speed 3000 RPM, 2300 G's, 18 x 80" bowl ID. 6.25" single lead hardsurfaced conveyor, 30 HP motor 460/3/60, 2-gear backdrive with 10 HP motor and VFD, feed tube, chutes and control panel mounted on a stand. 2005 vintage. Very good condition. Two available, priced separately.

Place Holder
Item 5389 - Decanter CHNX 944
Manufacturer
Alfa Laval
Model
CHNX 944B-31G

Alfa Laval CHNX 944 Decanters. Model CHNX944B-31G, serial 5023612 (one of them). Built 2007. Bowl 575mm. Decanter gear box 1:101 and 12 kNm DD. Includes controls. Main motor Baldor 100HP, 460/3/60 1785 rpm. Frame, bowl, motors, hood, controls, manual. All centrifuges were rebuilt including rotating assemblies in 2016. All centrifuge Preventive maintenance is up to date as of Apr 2019. Last used in ethanol industry. Qty (4) available, priced separately

Place Holder
Item 7769 - Flottweg Tricanter
Manufacturer
Flottweg
Model
Z23 3/441

Flottweg tricanter centrifuge Model Z23 with back drive. Type Z23 3/441. Unit has less than 100 hours on it. Includes manuals, starter cabinet and controls. Serial number 002.241.18. In three-phase separation, it is possible to separate two liquid phases from one solid phase at the same time. Built in 2013, reconditioned machine and controls in 2016. Very good condition

Place Holder